Engine Bearing Replacement – Learn How To Replace Engine Bearings

Engine Bearing Damage
Engine Bearing Damage

First of all, Engine bearing replacement is not as hard as it sounds.

So, If you have a bearing failure learning how to replace engine bearings can save you a ton of money.

Consequently, Doing your own engine bearing replacement can be very gratifying and give you a good sense of accomplishment.

So, Problems with engine bearings will usually result in some sort of knocking noise coming from your engine. The type of knocking noise that you hear will usually give you a good idea of which engine bearing is faulty or needs to be replaced.

Crankshaft
Crankshaft

Engine Bearing Replacement

1. Especially relevant before disassembly, number each connecting rod and matching cap according to cylinder location and each main bearing cap as to its location in the block.

2. Loosen cap screws and lift main bearing caps until free from block. Use cap screws as a lever to free stubborn caps.

3. Measure housing bore dimensions with a dial bore gauge or inside micrometers.

Measure Con-Rod Housing Bore
Measure Con-Rod Housing Bore

4. Use a micrometer to measure size, roundness and taper of the crankshaft.

Measure Crankshaft Journals
Measure Crankshaft Journals

5. One method to check the surface finish of a crankshaft is to rub a one cent coin several times across the surface of the shaft. If the shaft picks up copper from the coin, the shaft is too rough and must be reconditioned.

6. Also any burrs found at the oil holes of the crankshaft must be removed, using a stone, file or scraper.

7. All oil passages must be clean. Clean these passages with a brush and solvent. You can also use clean, dry, compressed air.

8. Select the correct part number and under size bearing to suit the engine application.

9. Using a clean, lint-free cloth, wipe bearing back and bore surfaces. They must be clean and dry. Furthermore, Never put anything between the bearing back and bore surface.

10. Also, Oil hole in block must line up with hole or slot in bearing to assure proper oil flow.

11.  All rubber crankshaft seals must be installed with the sealing lip pointing toward inside of engine.

12. Always, Use a good supply of lubricant on all bearing surfaces and seal lip.

13. Place the crankshaft gently and squarely onto the main bearings.  Install main caps in proper position.

14. All threads must be clean and lightly lubricated to obtain accurate torque readings.  Finally, Tighten all bolts and cap screws with a torque wrench to proper torque specifications. Do not attempt to guess at torque tightening.

Torque Wrench
Torque Wrench

15. In addition, With a feeler gauge of proper thickness, check clearance between crankshaft thrust disc and bearing flange surface.

16. Before installing piston and rod assembly, cover rod bolt threads with suitable protectors to prevent nicking of crankshaft. A short piece of rubber hose is good for this purpose.

17. Place matching number cap on connecting rod. Finally, Torque rod bolts to proper spec.

18. Priming the engine is most important. Consequently, This is to prevent dry start and premature damage to bearing surfaces.

Symptoms Of Faulty Engine Bearings

Engine Bearing Wear
Engine Bearing Wear

Problems with engine bearings will usually result in some sort of knocking noise coming from your engine.

Bad main bearing sounds:

  • If you hear knocking sounds when you start your car
  • And that sound continues while the engine is running
  • And the sound is coupled with low oil pressure warnings
  • This is a good indicator that your engine has bad main bearings

Bad rod bearing sounds:

  • In conclusion, If the knocking noise sounds more like striking a piece of tin or aluminium and increases in intensity as you accelerate, The most likely culprit is a faulty rod bearing.

Conclusion

The most important factor is lubrication. As long as there’s a steady flow of clean oil, The bearings will generally keep moving along fine. If the oil’s dirty, though, or if the oil supply is cut off, That’s when the problems start. As a result, At that point you need to decide if engine bearing replacement is your best choice.

Please Share DannysEnginePortal News